I’m looking for some Denys Brunton Magicolour 4-ply or something simliar so I can make a jacket using one of the patterns I’ve got. Can anyone advise on what wool is similar or where I can buy it?
Yours hopefully, Sandra
Hilda
Hilda
I’m looking for some Denys Brunton Magicolour 4-ply or something simliar so I can make a jacket using one of the patterns I’ve got. Can anyone advise on what wool is similar or where I can buy it?
Yours hopefully, Sandra
Hi
Can anybody tell me which ribber fits a Silver Reed SK155 machine?
You need a Silver Reed 155 ribber.
Heathercraft list them on their website so it might be worth contacting them.
Regards
Sue.
You need a Silver Reed 155 ribber.
Heathercraft list them on their website so it might be worth contacting them.
Regards
Sue.
Hello
I’ve recently bought a carter carriage KG-95. Everything was fine and I’ve knitted one half of a jumper but on the second half, after I’ve re-hanged the cast-on-comb, the needle has jammed. After changing the needle the garter carriage was knitting again with fine yarn but on the first row after casting on with double knit yarn it’s jammed again. I’ve changed three needles already. I was doing everything as it said in manuals and I feel so frustrated. Is this carriage so fragile? Is there anybody to help me with some advice and spare parts? Sorry, I didn’t mention, I’ve got a Brother KH-965. Please, somebody help me. Thank you
Hi
I’m new here. I bought these machines on eBay and they seem to be okay, but I just can’t get the cast-on process to work properly. It worked once on a trial run, but not since. Everything looks set-up and threaded properly, but the stitches don’t form. Can anyone give any advice please? Thanks
Sorry to hear you are having problems. The following may help.
Make sure the machine is clean.
Check that the gate pegs are upright and evenly spaced.
Check the spongebars in both beds. If the foam is flattened it will need replacing. Some people recommend using Silver Reed spongebars as replacements as Toyota ones are no longer available. Alternatively you can replace the foam with draught excluder taping round the ends to secure it.
Loosen the ribber setting screws at the ends of the beds and make sure the ribber is pushed against the mainbed as far as it will go before re-tightening them.
Check that the ribber connecting arm is seated properly – take it off and replace it making sure it sits on the positioning notches on the main carriage.
To start with try a 1×1 rib using alternate needles on each bed with the beds set at Full Pitch. Cast on with a tight tension position the comb and continue as book.
Hope this helps.
Regards Sue.
In a recent copy of the magazine it was mentioned that balls of wool can be used on a knitting machine but of course need to be waxed. How does one do that?
You need a wool winder and if you want to wax the yarn
a piece of a candle works well.
Find the ‘tail’ in the centre of the ball and let the yarn pass over the candle as you wind it. Wind each ball individually.
It is not always necessary to wax the yarn.
Balled yarn has a higher twist than coned yarn so you may need to knit with a looser tension.
Regards
Sue.
Metropolitan have these listed on their website. They are £11.80 for five. Sometimes they are advertised on eBay so it may be worth checking the listings.
Hope you manage to find some.
Regards Sue.
There are several listings on ebay at the moment for blank and pre-printed Mylar sheets.
I thought you might be interested.
Sue.
Metropolitan have these listed on their website. They are £11.80 for five. Sometimes they are advertised on eBay so it may be worth checking the listings.
Hope you manage to find some.
Regards Sue.
There are several listings on ebay at the moment for blank and pre-printed Mylar sheets.
I thought you might be interested.
Sue.
I know Christmas has gone but I’m hoping to be able to knit one for next year and I haven’t got a pattern. Can anyone help please?
Have you searched on Google?
There are lots of websites that have knitting patterns.
Even if you found a hand knitting pattern you could probably adapt it for the machine.
Regards
Sue.
Have you searched on Google?
There are lots of websites that have knitting patterns.
Even if you found a hand knitting pattern you could probably adapt it for the machine.
Regards
Sue.
I used my machine constantly for about five years and then, due to job change and 10-hour work days, put it a way for ten years. All of my support sources have closed up or moved away. I’m looking for users of Toyota machines and good sources of coned yarn. I’m also interested in buying a ribber for the KS901. Any help anyone can give will be greatly appreciated.
Thanks, Dianne
I have a Toyota 901 and am on the list of Knitting Buddies in MKM. I am happy to offer help and advice about this machine and machine knitting in general.
This machine will take the 501 or 506 ribbers. They sometimes are advertised on Ebay.
There are several good suppliers of yarn that advertise in MKM; Yeoman Metropolitan Undy Uppingham – they all have websites where you can purchase yarns. BSK have all their yarns for sale on Ebay. There are also other advertisers on Ebay that sell yarns some single cones and some bulk buys.
Hope this helps with your query.
Kind regards
Sue.
http://www.newtons.com/
Happy knitting…….Linda in VT
I have a Toyota 901 and am on the list of Knitting Buddies in MKM. I am happy to offer help and advice about this machine and machine knitting in general.
This machine will take the 501 or 506 ribbers. They sometimes are advertised on Ebay.
There are several good suppliers of yarn that advertise in MKM; Yeoman Metropolitan Undy Uppingham – they all have websites where you can purchase yarns. BSK have all their yarns for sale on Ebay. There are also other advertisers on Ebay that sell yarns some single cones and some bulk buys.
Hope this helps with your query.
Kind regards
Sue.
http://www.newtons.com/
Happy knitting…….Linda in VT
Chunky KH 260 Brother machine with Knit Leader KL116
Tension square knitted 20 stitches wide by 30 rows long. I used two strands of DK Shamal together on Tension 5.
Stitches using a centimetre ruler it measured 12 cm. (I tried using the blue ruler but it came out to silly numbers (17.5) and all the tension squares I knitted came out wrong so I used a CM ruler.) Read 12 on the CM ruler so I read off 12 on the tube and put the card into the machine for the stitches = (Card 12) 126 – 128.
Rows Measured with the blue ruler it came to 23 so as I was told that on a chunky machine you have to halve that number I put 11.5 into the machine. I was also told that both trippers have to be down so that it trips the sheet twice on each row and to leave the feeding lever plugged into the left hand side NOT to move the feeding lever to the right hand side and lift one tripper as this wouldn’t work properly? I drew a six inch square onto the Knit Leader and knitted it up – the stitches came out correct but I cannot get the rows right. Can someone please write down what to do from START ( tension square) to FINISH knitting a 6 inch square on the Knit Leader – step by step – as I’m getting so disheartened. I love this machine and am so desperate to get going. I have knitted a jumper from a magazine but I want to do my own thing and the Knit Leader seemed the way to go. Please help!
Firstly a note about the Blue Ruler. You cannot use it with the Knitleader. It is useful for finding how many stitches and rows measure 10cm (4″) if you want to work out your garment mathematically.
For detailed instructions on knitting a tension swatch see page 46 in the KH260 manual. Cast on over 40 needles knit several rows in main yarn and 2 rows contrast yarn. Now knit 15 rows using main yarn and the stitch you will use for your garment. Using a loop of contrast yarn knit needle 11 each side of centre 0 by hand then knit a further 15 rows. This gives 30 rows in main yarn. Now knit 2 rows contrast and several rows main yarn. Remove from machine. Roll the piece of knitting and give it a tug lengthwise to close the stitches.
Let it rest for at least a couple of hours and preferably overnight.
Now it is ready to be measured in millimetres. By the figure you give it will be 120 mm for 20 stitches. You should have a set of chunky stitch rules with your machine. Find number 11 it has orange ends and numbering and at one end you will see 120-122 printed on it. Put it into the Knitleader with this side showing. For the rows measure between the contrast rows in mm; this will give the measurement of 30 rows.
Set the Knitleader according to this measurement. Your KL book will explain in detail.
Both trippers on the main carriage have to be in working position.
When you feed the sheet into the Knitleader the stitch scale will indicate how many stitches to cast on for 6″ using scale 11 this will be 24 sts.
Now if you knit your trial piece it should come out the correct size. By the reading of 23 on the blue ruler you will have to knit about 34 or 35 rows for 6″.
I do hope this helps you to use your Knitleader.
Regards
Sue.
Firstly a note about the Blue Ruler. You cannot use it with the Knitleader. It is useful for finding how many stitches and rows measure 10cm (4″) if you want to work out your garment mathematically.
For detailed instructions on knitting a tension swatch see page 46 in the KH260 manual. Cast on over 40 needles knit several rows in main yarn and 2 rows contrast yarn. Now knit 15 rows using main yarn and the stitch you will use for your garment. Using a loop of contrast yarn knit needle 11 each side of centre 0 by hand then knit a further 15 rows. This gives 30 rows in main yarn. Now knit 2 rows contrast and several rows main yarn. Remove from machine. Roll the piece of knitting and give it a tug lengthwise to close the stitches.
Let it rest for at least a couple of hours and preferably overnight.
Now it is ready to be measured in millimetres. By the figure you give it will be 120 mm for 20 stitches. You should have a set of chunky stitch rules with your machine. Find number 11 it has orange ends and numbering and at one end you will see 120-122 printed on it. Put it into the Knitleader with this side showing. For the rows measure between the contrast rows in mm; this will give the measurement of 30 rows.
Set the Knitleader according to this measurement. Your KL book will explain in detail.
Both trippers on the main carriage have to be in working position.
When you feed the sheet into the Knitleader the stitch scale will indicate how many stitches to cast on for 6″ using scale 11 this will be 24 sts.
Now if you knit your trial piece it should come out the correct size. By the reading of 23 on the blue ruler you will have to knit about 34 or 35 rows for 6″.
I do hope this helps you to use your Knitleader.
Regards
Sue.
It sounds as if your ribber needs adjusting.
Do you have Mary Weaver’s ‘The Ribbing Attachment Part 2’? On page 282 she gives very detailed instructions for setting up the ribber correctly to eliminate problems.
There are too many instructions to copy here but I do hope you get it sorted.
Regards
Sue.
It sounds as if your ribber needs adjusting.
Do you have Mary Weaver’s ‘The Ribbing Attachment Part 2’? On page 282 she gives very detailed instructions for setting up the ribber correctly to eliminate problems.
There are too many instructions to copy here but I do hope you get it sorted.
Regards
Sue.